Tube Truss Fabrication: Cutting Chords and Webs to Fit

Tube truss fabrication goes faster when every chord and web member is cut to the joint it meets. Learn how gapped and overlapped HSS joints change the end cuts, and what to send Blueline in Chino, CA.

Quick Summary

  • A tube truss goes together fast when every chord and web member is cut to the joint it meets.
  • Gapped and overlapped joints need different end cuts, so name the joint type before you send files.
  • Equal-width members make sidewall welds harder, so profile cuts matter most there.
  • Send a model, a member list, and joint notes. Blueline cuts the tube parts in Chino, CA.

Tube truss fabrication works when every chord and web member arrives cut to the joint it will meet. Blueline Industries, a tube laser cutting shop in Chino, CA, cuts those members in a single operation so the fit-up crew assembles instead of reshaping. This post covers how hollow structural section (HSS) truss joints are built, what the cut has to do, and what to send a shop.

A truss is a frame of straight members joined into triangles. The long top and bottom members are chords. The shorter members between them are webs, also called branches.

Four step checklist for cutting tube truss chords and web members

What is tube truss fabrication?

Tube truss fabrication is the work of cutting hollow structural sections into chords and web members, then joining them into triangulated frames. Each web member must be cut so its end matches the chord face or the neighboring web it meets. That cut sets the gap, the weld access, and how quickly the frame goes together.

The Steel Tube Institute sorts HSS truss joints by how they carry force, not by how they look. Its HSS-to-HSS connections article names three types: K (which includes N), Y (which includes T), and X, also called cross.

You do not need to design the joint to order the parts. You do need to tell your cutting shop which joint each member end belongs to.

How do chord and web members meet?

Web members meet a chord at its face, and they meet each other at the same joint. In a gapped K joint, a small space sits between the two webs on the chord face. In an overlapped K joint, one web lands partly on the chord and partly on the other web.

The same article says overlapped joints give a stronger joint and a stiffer truss. It says gapped joints cost less and suit round members better.

Why the joint type changes the cut

A gapped joint needs two clean end profiles that stop short of each other. An overlapped joint needs one web cut to ride over the other. If you send both as plain angle cuts, the crew grinds the difference at the bench.

What the engineer decides first

Member sizes and wall thickness come from the engineer, not the shop. The Steel Tube Institute article says the lightest truss is not always the least costly, and that local strength at the joint can control the connection. Its rule of thumb is a chord width-to-thickness ratio between 15 and 30.

Blueline cuts to the drawing. It does not change the design.

Gapped or overlapped: what changes at the cut?

The joint type decides how many profiles a web member needs and how they relate. This table sums up what the Steel Tube Institute article says and what it means for the cut list.

JointWhat the source saysWhat it means for the cut listGapped KSpace on the chord face between the two webs. Less costly. Suits round members.Two end profiles that stop short of each other. Gap size comes from the drawing.Overlapped KOne web lands partly on the chord and partly on the other web. Stiffer truss.One web rides over the other. Mark which member is overlapped.Y or TA single web meets the chord.One end profile per web. Check the angle against the model.X (cross)Webs meet from both sides of the chord.Matching profiles on both sides. Keep the orientation clear.

Source: Steel Tube Institute, HSS-to-HSS Connections. The article's hidden toe note also matters for welders. At full overlap, it calls welding the hidden toe very important.

How does tube laser cutting help truss fit-up?

A tube laser cuts the end profile, the length, and any holes in one pass. The part comes off the machine shaped for its joint, so the fit-up crew does not grind or hand-scribe it. Single-operation cutting also removes handoffs between saw, drill, and coping stations.

That matters most when chord and web widths are equal. The Steel Tube Institute article says the sidewall weld in that case can be difficult to make. For larger members it suggests profiling the branch sidewall to contour to the radius of the chord.

A laser can cut that contour. A saw cannot.

What Blueline states about its process

Blueline runs LT7 tube lasers, rated at 4kW and fully automatic. According to Blueline, the machines handle tube up to 6 inches square or round on that line. Blueline also states tolerances of plus or minus 0.003 inch.

Those are the shop's own figures. Ask for them in writing against your drawing before you rely on them.

Blueline also states that single-operation processing reduces error rates by up to 70%. Treat that as a company claim, not a guarantee for your part.

What should you send with a truss cut list?

Send a 3D model or drawing, a member list, and a joint note for every member end. The list should name each chord and web, its size, wall thickness, material, and quantity. The joint note should say gapped, overlapped, Y, T, or X, plus the angle and any gap.

Here is a short checklist:

  1. Member mark, size, wall thickness, and material grade.
  2. Finished length and end profile for each end.
  3. Joint type at each end and which member overlaps.
  4. Hole and slot locations, dimensioned from one end.
  5. Weld prep or bevel notes, if any. Blueline lists 5-axis beveling capability.
  6. Finish and coating plans.

For related reading, see miter and cope cuts in structural tube and structural steel tube laser cutting for faster fit-up.

A scale reference from Blueline's work

Blueline worked on the Caltrans I-5 pedestrian bridge in Irvine in 2025, a project of more than 500,000 lbs of steel. That job is a reminder of why fit-up speed matters on infrastructure work. At that weight, small fit problems repeat many times.

Frequently asked questions

Does the shop design the truss joints?

No. The engineer of record sets member sizes, wall thickness, and joint type. Blueline cuts the tube parts to your drawing or model.

Can a tube laser cut the saddle shape on a web member?

Yes, a tube laser cuts end profiles from your model. Send the joint type and the chord size so the profile matches the face it meets. Ask Blueline to confirm the shape against your drawing before the run.

What is the difference between a chord and a web member?

Chords are the long top and bottom members of a truss. Webs are the shorter members between them that form the triangles.

Is a gapped or overlapped joint better?

Neither is better in every case. The Steel Tube Institute says overlapped joints give a stiffer truss and gapped joints cost less. Your engineer picks the type.

Does Blueline serve projects outside Chino?

Blueline operates from one facility in Chino, CA. It ships to and serves buyers in Portland, Tucson, San Francisco, San Diego, Seattle, Salt Lake City, Las Vegas, San Jose, and Los Angeles. See the service area page.

Next step

Send Blueline your truss model and member list, and name the joint at each end. Learn more about tube laser cutting for construction and infrastructure and precision slotting, notching, and hole cutting.

Get a Quote at bluelineind.com/contact-us or call (951) 833-5597.

Newsroom

The latest industry news
and insight from Flowpoint.

Tube laser machine with a long feed conveyor and lengths of steel tube on the shop floor
Normal to Surface Cuts in Tube Laser Cutting: Model It Right
Bundles of laser-cut steel tube with rows of round holes on a shop floor
Tube Laser Cutting Hole Size: Match Holes to Wall Thickness
Exterior of an LS5 laser cutting machine with control panel and warning light in a fabrication shop
Tube Wall Thickness vs Gauge: How to Call It on a Drawing
Forklift moving bundled steel tube stock in an outdoor yard beside a fabrication building
Metal Table Base Fabrication: Cut the Leg Joints Right
Blueline Industries graphic: packaging laser cut tube parts for shipping
Packaging Laser Cut Tube Parts for Shipping: What to Ask
Blueline Industries graphic: modular data center steel fabrication and tube parts that repeat
Modular Data Center Steel Fabrication: Tube Parts
Stack of rectangular steel tubes with cut holes inside a metal fabrication shop
Tube Laser vs Sheet Laser: Which Process Fits the Part?
Stacked rectangular steel tubes with laser-cut slots, tabs, and holes in a metal fabrication shop
Tab and Slot Tube Fabrication for Faster Field Assembly
Four cards: bow, twist, out-of-square and sag, tube variations to plan for before laser cutting
Tube Straightness and Laser Cutting: Plan for Bow and Twist
Four cards: freeze the revision, define the material, approve a first article, agree on checks
High Volume Tube Fabrication: Keep Every Part Identical
Infographic listing four causes of burrs and dross in laser cutting and what each one changes
Deburring Laser Cut Tube Parts: What Still Needs Hand Work
Tube handling and loading system on a shop floor with a bundle of steel tube beside it
Galvanizing Vent Holes in Tube: Cut Them In Early
Infographic comparing oxygen, nitrogen and compressed air as laser cutting assist gases
Assist Gas for Tube Laser Cutting: Nitrogen vs Oxygen
Infographic: five items to send a tube shop for an aerospace tooling frame order
Aerospace Tooling Frame Fabrication From Laser-Cut Tube
Graphic comparing ERW, DOM, and seamless tube, plus what to tell your shop.
ERW vs DOM vs Seamless Tube: What Matters for Laser Cutting
Four-step graphic: lock the revision, cut from one program, group by frame, prove one first.
Data Center Skid Frame Fabrication: Repeatable Tube Frames
Four step checklist for dimensioning machine frame tube from one datum
Machine Frame Tube Fabrication: Build From One Datum
Four step checklist for cutting tube truss chords and web members
Tube Truss Fabrication: Cutting Chords and Webs to Fit
Five-step process for approving first article tube parts before a production run
First Article Tube Parts: Approve a Run Before Release
Four-step checklist for calling out precision tube cutting tolerances on a drawing
Precision Tube Cutting Tolerances: How to Call Them Out
Infographic: four checks for square tube corner radius before laser cutting
Square Tube Corner Radius: What It Changes in Laser Cutting
Infographic: four rules for where to place the weld seam on laser-cut and bent steel tube
Tube Weld Seam Orientation: Where the Seam Should Sit
Infographic of four things to compare between fiber and CO2 lasers for tube cutting
Fiber vs CO2 Laser for Tube Cutting: What Matters
Infographic of five checks before cutting thin wall tube with a laser, from naming the tube to prototyping first
Thin Wall Tube Laser Cutting: Protect the Walls
Infographic of tube material waste sources: offcuts, end scrap, part length, and cut list
Tube Laser Nesting: How Layout Affects Material Yield
Infographic of five items to send in a data center RFQ: design data, material, finish, scope, delivery
Data Center Fabrication RFQ Checklist: What to Send a Tube Shop
Six-card checklist for inspecting laser cut tube parts: identity, size, end cuts, features, edges and records
Inspecting Laser Cut Tube Parts: A Receiving Checklist
Six-card checklist: size and grade, cut features, end conditions, finish, delivery order and spec requirements
Steel Fabrication for Infrastructure California: Scope First
Infographic listing five steps to settle before cutting tube, from nominal sizes to a first piece check
What Is Kerf in Tube Laser Cutting? Slot Fit Explained
Infographic listing six items to send with a roll cage notch list, from tube size and wall to part label
Roll Cage Tube Notching: How to Spec Your Cut List
Infographic comparing miter and cope cuts in structural tube with gap and file checklist
Miter and Cope Cuts in Structural Tube: Choose by Joint
Infographic: four steps for metal furniture frame fabrication, from tube profile to first run
Metal Furniture Frame Fabrication: Plan the Finish First
Blueline Industries graphic: heat affected zone in tube laser cutting and what to put on the drawing
Heat Affected Zone in Tube Laser Cutting: A Plain Primer
Blueline Industries graphic: nitrogen cooling tube site checks, a receiving checklist for fabricated stainless tube
Nitrogen Cooling Infrastructure Tube Fabrication Checks
Blueline Industries Honored at the Illuminate Life Gala
Blueline infographic: five-step tube laser prototype loop from questions to revision
Tube Laser Prototyping Services: Iterate Before You Commit
Blueline infographic: five checks before sending large diameter tube for laser cutting
Large Diameter Tube Laser Cutting: Plan the Fit-Up First
Infographic: five design checks for tube laser cutting, from hole size to weld seam location
Design for Tube Laser Cutting: Choices That Cut Rework
Infographic: five items to send when a custom tube part changes, from part number and revision to parts already cut
Custom Tube Fabrication for OEMs: Handling Design Revisions
Infographic: what to specify for chassis tube and exhaust tube before laser cutting
Chassis and Exhaust Tube Laser Cutting: Steel vs Stainless
Infographic: notch, cope, miter, and bevel cuts a tube laser makes in one pass
Tube Notching and Coping: Joints That Fit Off the Machine
Infographic: four places errors enter a tube part, from re-clamping to old revisions
How to Reduce Fabrication Errors With Single-Operation Cutting
Infographic: four tube laser joint features that make furniture frames repeat
Furniture Tube Laser Cutting: Build Frames That Repeat
Blueline infographic: five items in a Las Vegas quote packet for a Chino, CA tube laser shop
Tube Laser Cutting Las Vegas: Shipping Work In From Chino, CA
Blueline infographic: five items a complete data center fabrication release needs before parts are cut
Data Center Construction Fabrication Lead Times Explained
Infographic: four questions that decide stainless vs carbon steel tube, covering exposure, edge, paint and duty
Stainless vs Carbon Steel Tube for Fabrication: How to Choose
Infographic: four steps from drawing to install for stage tube parts, from sending the model to shipping in install order
Fabrication for Stage and Entertainment Structures: Parts That Fit Fast
Infographic: five questions to ask when choosing a tube fabrication partner
How to Choose a Tube Fabrication Partner: Questions to Ask
Infographic: four steps to design laser cut tube assemblies where parts locate themselves with slots and tabs
Laser Cut Tube Assemblies for OEMs: Parts That Self-Locate
Infographic comparing square, rectangular, and round tube by load direction, twisting, and joints
Square vs Round vs Rectangular Tube: How to Choose
Infographic comparing air bending, bottoming, and coining in press brake bending
What Is Press Brake Bending? A Shop-Floor Primer
Infographic: five steps for how a Chino shop delivers laser-cut tube parts to Los Angeles buyers
Tube Laser Cutting Los Angeles: What a Chino Shop Ships You
Infographic: four steps from CAD file to a proven tube prototype, ending in revise and scale
Aerospace Tube Prototypes: Prove the Geometry Fast
Stack of square steel tubes on a table in a fabrication shop
Tube Laser vs Waterjet for Tube: Matching Process to Part
Four-step graphic: start from the schedule, bundle by assembly, mark every part, release in phases
Data Center Steel Fabrication: Ship Parts in Install Order
Blueline logo on a glass entrance door beneath an OFFICE sign
Tube Laser Cutting San Jose: What to Send for a Chino Quote
Infographic: four checks for exposed tube joints, from seam placement to a clean model
Architectural Steel Tube Cutting for Exposed Joints
Infographic: what is 5-axis tube beveling, four steps from tilting the head to fit and weld
What Is 5-Axis Tube Beveling? A Weld-Prep Primer
Infographic: count the steps on every part, tube laser versus saw and drill, in four steps
Tube Laser vs Saw and Drill: Counting Steps Per Part
Blueline Industries at FABTECH 2026 Las Vegas: Meet Our Tube Laser Cutting Team
Operator using the control panel of an industrial laser machine on a shop floor
Tube Laser Cutting Salt Lake City: Sending Work to Chino, CA
Infographic: four sources of tube laser cutting tolerance: the tube, the drawing, the features and the process
What Tolerances Can Tube Laser Cutting Hold?
Blueline infographic: six factors that affect tube laser cutting cost
What Affects Tube Laser Cutting Cost? Factors, Not Prices
Blueline infographic: six items to send with an aftermarket tube fabrication quote request
Automotive Aftermarket Tube Fabrication: Fit Before Finish
Infographic: five steps of a first tube laser order from Chino, CA
Tube Laser Cutting Seattle: Your First Order From Chino, CA
Infographic: four checks for choosing stainless tube for cooling systems
Stainless Steel Tube Fabrication for Cooling Systems
Blueline checklist of six material details to give a tube laser cutting shop
What Materials Can a Tube Laser Cut? Steel to Aluminum
Blueline checklist of six items to send with a structural tube quote request
Structural Steel Tube Laser Cutting for Faster Fit-Up
Glass entrance door with the Blueline logo at a Blueline building
Tube Laser Cutting San Francisco: Buying From Chino, CA
Bundle of square steel tube in a fabrication shop with a tapping machine and equipment in the background
Short Run Tube Fabrication: Prove the Design Before Scaling
Blueline graphic: What tube sizes can a tube laser cut, profiles and diameters
What Tube Sizes Can a Tube Laser Cut? Capacity Explained
Blueline graphic: Prepare your CAD files for tube laser cutting, a pre-send checklist
How to Prepare CAD Files for Tube Laser Cutting
Blueline infographic: five-item spec package checklist for aerospace tube laser cutting
Aerospace Tube Laser Cutting: A Spec Checklist for Engineers
Blueline infographic: five steps of a Tucson tube laser cutting order from Chino, CA
Tube Laser Cutting Tucson: Ordering From a Chino, CA Shop
Infographic on choosing tube laser or plasma: wall thickness, features, edge and weld, volume
Tube Laser vs Plasma Cutting: Which Fits Your Tube Job?
Infographic listing four items to send for a data center support quote: geometry, tube spec, material, fit and finish
Tube Laser Cutting for Data Center Supports: What to Specify
Blueline Industries graphic: tube laser cutting for Portland buyers from Chino, CA
Tube Laser Cutting Portland: Working With a Chino Shop
Blueline Industries graphic: tube laser cutting for bridge fabrication
Tube Laser Cutting for Bridge Fabrication: What to Ask
Hiring For Hearth: Blueline Industries Builds A Culture for Growth
How tube laser cutting improves roll cage fabrication
How to get a tube laser fabrication quote for your manufacturing OEM project
Tube Laser Cutting San Diego, CA: Services, Capabilities, and How to Get a Quote
Custom Metal Furniture Frames: A Manufacturer's Guide to Tube Laser Cutting
Tube Laser Cutting Explained: How It Works and Why It Matters for Manufacturers
Tube Laser Cutting: What It Is and How It Works
CNC Tube Cutting vs. Manual Fabrication: Why Production Shops Are Making the Switch
Tube Laser Cutting Services: A Complete Guide for OEMs, Contractors, and Engineers
Why AI Data Center Builders Are Switching to Tube Laser for Nitrogen Cooling Infrastructure
Structural Steel Fabrication for Data Center Construction: Meeting the Demands of AI-Scale Infrastructure
Custom Tube Fabrication for High-Volume Production: What to Look for in a Fabrication Partner
Structural Steel Fabrication for California Infrastructure: What GCs Need to Know About Tube Laser Processing
The Hidden Bottleneck in Data Center Construction and the Fabrication Technology Solving It
Stainless Steel Fabrication for Data Centers: How Single-Process Cutting Reduces Lead Times by Weeks